DC switchgear type RT-1

Home page/Offer/Products/DC devices/DC switchgear type RT-1

Purpose

Indoor switchgear type RT-1 is dedicated to power supplying trolleybus, tram and subway traction. Innovative solutions provide safe and easy operating and enables the switchgears to be installed in maintenance-free stations.

General characteristics

RT-1 switchgears are made with metal housing, air insulated and equipped with newest switching devices. In default configuration by-pass bar is used. RT-1 switchgear is built of following standardized panels:

  • withdrawable feeder panel, metal-clad, equipped with high-speed circuit-breaker, line test devices on a withdrawable unit with by-pass bar and disconnector with motor drive, cable terminal compartment and auxiliary circuits compartment,
  • rectifier units panel, metal-clad, equipped with bipolar disconnector with motor drive, designed for power distribution between rectifier and RT-1 switchgear. Control and measurement units for rectifier and internal load of the substation are installed in the front part of RT-1 switchgear,
  • Negative cables panel connected with busbar („-”; „+”) by disconnectors, current measurement on each cable,
  • Spare circuit-breaker panel is the same as feeder panel but without disconnector on bypass busbar and cable terminals,
  • Sectional disconnector panel, metal-clad, designed to separate main busbar into sections without by-pass bar, equipped with unipolar disconnector with motor drive.

Withrawable units contains of fixed part and trolley. Between them there are following connections:

  • Sliding to main busbar and cable terminal
  • Sliding to earthing terminal
  • plug to control and signal cable

Features

The most important advantages of RT-1 switchgear are:

  • compact design with air insulation
  • metal-clad separation provides protection against effects of arc
  • system of interlocks preventing from connection errors
  • switching the position of trolley with door closed - locate or remote
  • barriers protecting the fixed contacts
  • newest devices installed
  • easy and safety operating
  • convenient service and maintenance
  • innovative design
  • screw connections provides easy modernization and extension

Very small size of RT-1 switchgear enables to make a savings in investment process (minimalized surface and volume of the substation building). Innovative design provides safety during operation.

RT-1/36-O DC switchgear in „Krucza” substation in Poland

  1. Auxiliary circuits compartment (PP)
  2. Circuit-breaker compartment (PW)
  3. Cable terminals compartment
  4. Main busbar compartment („-”; „+”) (negative cables)
  5. By-pass busbar compartment („+”; „-”)
  6. Main busbar compartment („+”; „-”)
  7. Withdrawable unit
    1. Trolley
    2. Drawer
    3. High-speed circuit-breaker
  8. Feeder circuits contacts
  9. Cable terminals
  10. Auxiliary circuits compartment door
  11. Circuit-breaker compartment door
  12. Auxiliary circuits compartment back door
  13. Back door
  14. Disconnector with motor drive

Technical data

Type of the switchgear RT-1
Rated voltage V 660 / 850 DC
Rated insulation voltage V up to 1000
Power frequency withstand voltage
circuit-breaker and disconnector in „SERVICE” position
circuit-breaker and disconnector in „TEST” position

kV
kV

5,5
5,5
Rated impulse withstand voltage of isolation
circuit-breaker and disconnector in „SERVICE” position
circuit-breaker and disconnector in „TEST” position

kV
kV

12
12
Rated current:   
main busbars
by-pass bar
of unit with short-circuiting switch
A
A
A
9000
5000
4000
Rated short-time withstand current
main busbars and feeder
by-pass bar
protective circuit PE

kA/s
kA/s
kA/s

106/1
70/0,25
35/0,25
Short-circuit peak current
main busbars and feeder
by-pass bar
protective circuit PE

kA
kA
kA

150
100
50
Degree of protection   IP 4X
Dimensions of cubicles:   
width
height
depth
mm
mm
mm
600
2220
1500
Design   indoor
Compliance with standards   PN-EN 50123-1, PN-EN 50123-2, PN-EN 50123-6, PN-EN 60529

Product card in pdf formatDC switchgear type RT-1 plik .pdf

Ask for a product
+48 63 24 66 348

I agree to the processing of my personal data by ELEKTROBUDOWA SA, the company with the registered office in Katowice at 12, Porcelanowa Street, in order to:
Information clause for a person giving consent to the processing of personal data in connection with sending information about products

In accordance with Article 13 paragraphs 1 and 2 of General Data Processing Regulation of 27 April 2016, I inform that:

The Controller of provided personal data is: ELEKTROBUDOWA SA with the registered office in Katowice at 12, Porcelanowa Street.

ELEKTROBUDOWA SA appointed a person responsible for protection of personal data, whom you can contact by letters sent to the postal address of the controller, telephone number 32 25 90 100 between 9.00 -15.00 and by e-mail: rodo@elektrobudowa.pl

Your personal data will be processed and stored only for the purpose of sending complete information about product and, if the consent is given, for sending information about products and services offered by ELEKTROBUDOWA SA.
Personal data will be stored until full information about product is sent, and if the consent is given for regular sending information about products, until this consent is withdrawn.

Personal data of subscribers are available to IntraCOM.pl, a company with registered office in Katowice, at 9a, Jesionowa Street.

You have the right to request access to your personal data (Article 15 of the Regulation), the rectification (Article 16 of the Regulation), the right to data transfer (Article 20 of the Regulation) as well as, in cases specified in the Regulation (Article 17) the right to erasure and to restriction of data processing (Article 18 of the Regulation).

In accordance with Article 21 of the Regulation, you have the right to object to processing of your personal data. Such an objection will make it impossible to include your email address in the process of sending out information about products and services offered by ELEKTROBUDOWA and will be treated as unsubscribing to this information.

If you decide that the processing of your personal data violates provisions of the Regulation, you have the right to submit a complaint to the supervisory body, that is to Personal Data Protection Office.

In accordance with Article 7 of the Regulation, you have the right to withdraw your consent to the processing of your personal data. Withdrawal of consent consists in sending an e-mail message with its subject containing the information: "Withdrawal of consent to the processing of provided personal data”.
* required fields
do góry